Hydraulic chucks for swiss-type automatic lathes. The lathe type hydraulic chuck was developed from decades of knowledge accumulated on milling machines. In addition to high accuracy and rigidity, the slim design helps avoid interference with adjacent tools.
HYDRAULIC CHUCKS FOR SWISS-TYPE AUTOMATIC LATHES
HYDRAULIC CHUCKS
HYDRAULIC CHUCKS FOR SWISS-TYPE AUTOMATIC LATHES Hydraulic chuck system provides high accuracy and easy tool changes.
Improved Accuracy and Rigidity The lathe type hydraulic chuck was developed from decades of knowledge accumulated on milling machines. In addition to high accuracy and rigidity, the slim design helps avoid interference with adjacent tools.
Safe and Quick Operation The ability to change cutting tools with a single T-wrench drastically reduces the time required for tool changes. It also reduces the need to work in extremely limited spaces and improves operator safety.
±1μm Repeatability Even changing the tool, the repeatability at 4D is stable at ±1μm or less. In addition, the tightening is completed when the clamping screw hits the bottom, controlling tightening torque is not needed.
No Change in Tool Length Since the tool projection length does not change after the clamping, it is easy to control the tool projection length in the machine.
Repeatability Less than 1μm
No Change
Hydraulic Chuck
4D
Collet Chuck
THREE TYPES FOR DIFFERENT TOOL POSTS Standard Type F Type
R Type
•Tighten from the tool side. •Coolant delivery is possible with Rc(PT)1/8 screw. •An adjusting screw can also be fitted (some models). •Length can be adjusted by cutting the shank. •Easy to install in various tool posts.
•Tighten from the opposite side of the tool. •Coolant delivery is possible with Rc(PT)1/8 screw. •Optimum overall length for easy use. • Ideal for use on a front tool post.
•Unique design for use with both upper and lower sections without interference. •Tightening at an offset position in the tool side. •Coolant delivery with M6 is possible when mounted on the upper section.
2
HYDRAULIC CHUCKS
Tightening from the opposite side of the cutting tool
F Type
Standard Type
View of Swiss-Type Lathe Machine
Front Tool Post (Tool Post 1)
Main Spindle
Counter Tool Post (Tool Post 2)
Rear-End Tool Post
Sub Spindle (Counter Spindle)
Easy handling of cutting tools by avoiding adjacent tools
標準タイプ Standard Type
R Type
3
HYDRAULIC CHUCKS
HYDRAULIC CHUCK LATHE TYPE — STANDARD TYPE CLAMPING RANGE: ø3-12mm High-precision cutting with hydraulic chuck is achieved on an automatic lathe.
COOLANT
THROUGH
H
E
G
Rc(PT)1/8
L 1
A
L
W
Catalog Number
Weight (lbs.)
ød
øDs
L
L 1
A
B 1
B 2
W
H
E
G
.4 .4 .4 .4 .4 .4 .4 .5 .5 .5 .5 .6 .6 .6 .6 .5 .7 .7 .7 .7 .6 .6 .8 .8 .8 .8 .7 .7
SL19.05-HDC3-60*
3mm
.787-1.26
.63
-HDC3.175-60*
.125
HDA4-05015W
-HDC4-60
4mm .1875 6mm
.905-1.26
.75
.91
-HDC4.7625-60
.750
2.36 1.18
.59
.62
.87
-HDC6-60
1.22-1.89
.98
NBA6B
-HDC6.35-60
.250
-HDC8-60
8mm 3mm 4mm 6mm 8mm 3mm 4mm 6mm 8mm
.95
2.56
1.22
—
.787-1.26 .905-1.26 1.22-1.89
.63 .75 .98
SL20-HDC3-70*
HDA4-05015W
-HDC4-70 -HDC6-70
.91
.787
2.75 1.18
.59
.62
.90
NBA6B
.95
2.95
1.22
—
-HDC8-70 v
.787-1.26 .905-1.26 1.22-1.89
.63 .75 .98
SL22-HDC3-70*
HDA4-05015W
-HDC4-70 -HDC6-70
.91
.62
.866
2.75 1.18
.59
.98
NBA6B
.95
2.95 2.76
1.22 1.30
-HDC8-70 v -HDC10-70 v
—
10mm
1.06
.66
3mm 4mm 6mm 8mm
.787-1.26 .905-1.26 1.22-1.89
.63 .75 .98
SL25-HDC3-65*
.91
.55
HDA4-05015W
-HDC4-65 -HDC6-65
.91 .95
.59 .63 .67 .71
NBA6B
.984
2.56 1.57
.59
1.10
2.76
1.22 1.30 1.42
-HDC8-65 v -HDC10-65 v -HDC12-65 v
10mm 12mm
1.06
—
2.56
28
3mm 4mm 6mm 8mm
.787-1.26 .905-1.26 1.22-1.89
.63 .75 .98
SL25.4-HDC3-80*
.91
.55
HDA4-05015W
-HDC4-80 -HDC6-80
.91 .95
.59 .63 .67 .71
NBA6B
1.000 3.15 1.57
.59
1.10
3.35
1.22 1.30 1.42
-HDC8-80 v -HDC10-80 v -HDC12-80 v
10mm 12mm
1.06 1.10
—
3.15
Use only cutting tools that have a shank tolerance of h6. Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E.” ! CAUTION
*Some coolant comes out from the inner slots in the coolant-through application • Adjusting screws cannot be used with models marked v • Adjusting screw is adjustable both from the head and shank ends • “E” is the min. clamping length • “G” is the adjusting screw (optional) • “H” indicates the adjustment length with an adjusting screw • “H” at HDC8/10/12 is the max. tool shank length can be inserted for these models • L 1 is the minimum length, in case of shortening the shank
4
HYDRAULIC CHUCKS
HYDRAULIC CHUCK LATHE TYPE — F TYPE CLAMPING RANGE: ø3-10mm Single wrench enables easy cutting tool change on the tool post. User-friendly rear clamping design is ideal for front tool post.
H
Rc(PT)1/8
E
L 1
L
A
W
Catalog Number
Weight (lbs)
ød
øD
øDS
L
L 1
A
B
W
H
E
SL19.05F-HDC3-85*
3mm 4mm 6mm 8mm 3mm 4mm 6mm 8mm 3mm 4mm 6mm 8mm
.63 .75
.551
3.35
.20
2.99
.53
-HDC4-85 -HDC6-80 -HDC8-80
.752
.67
.53
.87
1.00 1.22
.50 .46
—
3.15
—
2.80
SL20F-HDC3-75*
.63 .75
.551
2.95
.20
2.60
.53
-HDC4-75 -HDC6-70 -HDC8-70
.787
.67
.53
.91
1.00 1.22
.50 .46
—
2.76
—
2.40
SL22F-HDC3-75*
.63 .75
.551
2.95
.20
2.60
.62
-HDC4-75 -HDC6-70 -HDC8-70 -HDC10-70
.787
.67
.53
.98
1.00 1.22 1.30
.57 .55 .50
—
2.76
—
2.40
10mm
*Some coolant comes out from the inner slots in coolant-through application • Adjusting screw cannot be used • “E” is the min. clamping length • “H” indicates the adjustment length with an adjusting screw
F Type •Tighten from the opposite side of the tool. •Coolant delivery is possible with Rc(PT)1/8 screw. •Optimum overall length for easy use. • Ideal for use on a front tool post.
Use only cutting tools that have a shank tolerance of h6. Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E.” ! CAUTION
5
HYDRAULIC CHUCKS
HYDRAULIC CHUCK LATHE TYPE — R TYPE CLAMPING RANGE: ø3-10mm Unique block design enables easy handling for both upper or lower tool post position. Oil hole drills can be used for coolant delivery with M6.
H
E
12.5
2-ø4.5
M6
L 1
12.5
25
L
W 1
W 2
Catalog Number
Weight (lbs)
ød
øD
L
L 1
W 1
W 2
H
E
SL22R-HDC3-40*
3mm 4mm
.28 .35 .20
1.38 1.65 2.17
.63 .75 1.0 1.2 1.3
.75 .73 .79 .79 .77
.551
-HDC4-40 -HDC6-40 -HDC8 -40 -HDC10-40
.65
6mm .709 8mm .787 10mm .866
1.57
.65
.24
.69
2.13
*Some coolant comes out from the inner slots in the coolant-through application • Adjusting screw cannot be used • “E” is the min. clamping length
R TYPE •Unique design for use with both upper and lower sections without interference. •Tightening at an offset position in the tool side. •Coolant delivery with M6 is possible when mounted on the upper section.
Use only cutting tools that have a shank tolerance of h6. Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E.” ! CAUTION
2600 Huntington Blvd | Hoffman Estates, IL 60192 | P: (224) 770-2999 | F: (224) 770-2997 | bigdaishowa@us.bigdaishowa.com | www.bigdaishowa.com
Page 1 Page 2 Page 3 Page 4 Page 5 Page 6Powered by FlippingBook