HYDRAULIC CHUCKS
Catalog Number
Min Clamping Length E
Adjusting Screw
Weight (lbs.)
Fig.
ød
øD øD 1
øD 2
L
L 1
L 2
H
BBT30-HDC6-45
.28
1.38-1.97
HDA6-05020
1.5
1 2
1.181 1.81
1.77 2.95 3.54 4.13 1.77 2.95 3.54 4.13 1.77 2.95 3.54 4.13 1.77 2.95 3.54 4.13 3.54 1.77 2.95 3.54 5.91
—
—
-75 -90
1.57
1.8
6mm
1.10
1.024 1.79
2.24 2.83
1.10-1.97
HDA6-05032
3
1.22
1.69
-105
2.0 1.5 1.8
-HDC8-45
1 2
1.260 1.81
.28
1.38-1.97
HDA8-06020
—
—
-75 -90
1.61
8mm
1.10
1.102 1.79
2.24 2.83
1.10-1.97
HDA8-06032
3
1.30
1.73
2.0
-105
-HDC10-45
.28
1.77-2.17
HDA10-08015
1.5 2.0
1 2
1.339
—
—
-75 -90
10mm
1.30
1.81
1.181
1.30 1.42
1.42
2.01 2.60
1.30-2.17
HDA10-08032
3
2.2
-105
-HDC12-45
1 2
1.417
.28
— 2.17-2.36
1.5 1.8 2.0 2.2 2.0 1.5 2.0 2.2 2.3
HDA12-10010 z
—
-75 -90
1.42
12mm
1.81
1.50
1.260
1.38 1.50 1.46
2.01 2.64
1.50-2.36
HDA12-10032
3
1.77
-105
-HDC14-90
14mm
3 1 2
1.339 1.81
1.81
2.05 1.50-2.36
1.50
HDA12-10032
1.654
.28
2.76
—
-HDC16-45
-75 -90
1.38
HDA16-12030
16mm
1.81
—
—
1.69
1.496
1.69-2.76
3
1.85
HDA16-12037
-150
— 2.36
— .55 1.69-2.13
-HDC20-60
HDA16-12030
2.0
-75 -90
4
2.09
1.81
2.95 3.54
.63
1.02 1.81-2.76
20mm
1.496
1.69
1.22 1.57 1.73 1.54
1.61
2.4 2.2 3.8 4.0
1.69-2.76
HDA16-12037
-150
3 4 4
1.81
— 5.91 — 4.13 — 4.13
—
-HDC25-105 -HDC32-105
25mm 32mm
2.165 2.48 2.362 2.95
— 2.05-3.15 — 2.20-3.15
2.05 2.20
HDA25-16039 HDA25-16039
• “H” indicates the adjustment length with an adjusting screw • Adjusting screws cannot be used with models marked • Straight collets cannot be used with models marked • In case the projection length needs to be adjusted from the shank side, add the letter “W” to adjusting screw model number for hexagon sockets on both sides (ex: HDA6-05020W), adjusting screw with z indication is not available in W type
Use only cutting tools that have a shank tolerance of h6 (see table Pg. 26). Do not use with cutting tools made with a flat on the shank (ie: Weldon type shank). Roughing end mills are not recommended for use with HYDRAULIC CHUCKS. Do not tighten the clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”. ! CAUTION
ACCESSORIES
PERFECT SEAL/ JET COLLET PG. 361
127
Powered by FlippingBook